ES-9022 Rev.3
R30PA2
Remote I/O R30 Series
TOTALIZED PULSE INPUT MODULE
(Pi 2 points, 32 Bits)
Functions & Features
• Space-saving remote I/O module of 2 points input pulse counter
• 32-bit binary data
MODEL: R30PA2S[1]
ORDERING INFORMATION
• Code number: R30PA2S[1]
Specify a code from below for [1].
(e.g. R30PA2S/Q)
• Specify the specification for option code /Q
(e.g. /C01/SET)
NO. OF CHANNELS
2
: 2
COMMUNICATION MODE
S
: Single
[1] OPTIONS
Other Options
blank
: none
/Q
: Option other than the above (specify the specification)
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to our web site.)
/C01
: Silicone coating
/C02
: Polyurethane coating
/C03
: Rubber coating
EX-FACTORY SETTING
/SET
: Preset according to the Ordering Information Sheet
(No. ESU-9022)
RELATED PRODUCTS
• Interface module
Model: R30NECT1 (firmware version V1.04.10 or higher)
Model: R30NCIE1 (firmware version V1.01.13 or higher)
• Paperless recorder
Model: TR30 (firmware version V1.05 or higher)
• PC configurator software (model: R30CFG)
Downloadable at our web site.
For connecting to PC, use commercially available Mini-B type USB cable. (provided by user)
GENERAL SPECIFICATIONS
Connection
Internal bus
: Via the Installation Base (model: R30BS)
Input
: M3 separable screw terminal (torque 0.5 N·m)
Internal power
: Via the Installation Base (model: R30BS)
Solderless terminal
: Refer to the drawing at the end of the section.
Recommended manufacturer
: Japan Solderless Terminal MFG. Co., Ltd., Nichifu Co., Ltd.
(Solderless terminals with insulation sleeve do not fit.)
Applicable wire size
: 0.25 to 0.75 mm
2
Screw terminal
: Nickel-plated steel
Isolation
: Input or reset input or external power to internal bus or internal power
Status indicator LEDs
: RUN, ERR
Input status indicator LEDs
: Green LED; turns on with input ON
(Refer to the instruction manual.)
Count reset
: by inputting one pulse to the reset input terminal, or from host PC/PLC
Count preset
: settable from host PC/PLC, or with PC configurator software
■Recommended solderless terminal size - M3 (unit: mm)
INPUT SPECIFICATIONS
Module type: Pulse input, 2 points
Common: Positive or negative common (NPN/PNP), common per 2 points
■
Contact Input / Reset Input
•
Open collector input (NPN, PNP)
Rated input voltage
: 24 V DC ±10 %; ripple 5 %p-p max.
ON voltage/current
: ≥ 16 V DC (input to common) /
≥ 3.7 mA
OFF voltage/current
: ≤ 5 V DC (input to common) / ≤ 1 mA
•
Voltage Pulse Input
ON voltage/current
: ≥ 16 V DC (input to common) /
≥ 3.7 mA
OFF voltage/current
: ≤ 5 V DC (input to common) / ≤ 1 mA
Input current
: ≤ 5.5 mA per point at 24 V DC
Input resistance
: Approx. 4.4 kΩ
ON delay
: ≤ 2.0 msec.
OFF delay
: ≤ 2.0 msec.
Max input frequency
: 100 Hz
Minimum pulse width time requirement
: 5 msec. (for both ON and OFF)
Totalized pulse range
: 0 to 4,294,967,295 (0 only when the counter is reset)
Max pulse range
: 1 to 4,294,967,295
(factory setting: 4,294,967,295)
Count at overflow
: 0 or 1 (factory setting: 0)
INSTALLATION
Current consumption
: 30 mA max.
Operating temperature
: -10 to +55°C (14 to 131°F)
Storage temperature
: -20 to +65°C (-4 to +149°F)
Operating humidity
: 10 to 90 %RH (non-condensing)
Atmosphere
: No corrosive gas or heavy dust
Mounting
: Installation Base (model: R30BS)
Weight
: 150 g (0.33 lb)
PERFORMANCE
Data allocation
: 4
Insulation resistance
: ≥ 100 MΩ with 500 V DC
Dielectric strength
: 1500 V AC @ 1 minute
(input or reset input or external power to internal bus or internal power)
1500 V AC @ 1 minute (power to FG; isolated on the power supply module)
STANDARDS & APPROVALS
EU conformity
:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
RoHS Directive
CONFIGURATOR SOFTWARE SETTING
The following parameters can be set with using PC Configurator Software (model: R30CFG)
Refer to the users manual for the R30CFG for detailed operation of the software program.
EXTERNAL VIEW
TERMINAL ASSIGNMENTS
DATA ALLOCATION
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM