·Some details are not shown. Please refer to specification sheets for all information.

IT60RE

Tower Light Series

ETHERNET TOWER LIGHT
(60 mm dia., 4 layers)

Functions & Features
• Lighting, blinking and buzzing available with PLC or PC via Modbus/TCP.
• Bi-color lighting available in fourth layer
• Separable tension clamp terminal

MODEL: IT60RE-4[1][2][3][4][5]D[6]-[7][8]

ORDERING INFORMATION
• Code number: IT60RE-4[1][2][3][4][5]D[6]-[7][8]
Specify a code from below for each [1] through [8].
 (e.g. IT60RE-4RYGBWD1-M2/Q)
• Specify the specification for option code /Q
 (e.g. /C01)

LAMP LAYERS
4: 4 layers

[1] LAMP 1 COLOR
(1st layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[2] LAMP 2 COLOR
(2nd layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[3] LAMP 3 COLOR
(3rd layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[4] LAMP 4 COLOR
(4th layer from the top)
R: Red
Y: Amber
G: Green
B: Blue
W: White

[5] LAMP 5 COLOR
R: Red
Y: Amber
G: Green
B: Blue
W: White
N: None

MOUNTING
D: Direct mounting

[6] DESIGN TYPE
1: Type 1
2: Type 2 (with dummy antennae)
(refer to outline dimensions)

[7] POWER INPUT
AC Power
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
 47 – 66 Hz)
DC Power
R: 24 V DC
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)

[8] OPTIONS
blank: none
/Q: With options (specify the specification)

SPECIFICATIONS OF OPTION: Q
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
/C03: Rubber coating

RELATED PRODUCTS
• PC configurator software (model: ITCFG)
Functions are configurable using the PC Configurator Software.
Downloadable at M-System’s web site.
A dedicated cable is required to connect the module to the PC.  Please refer to the internet software download site or the users manual for the PC configurator for applicable cable types.

GENERAL SPECIFICATIONS
Degree of protection: IP 65, vertical mounting only (bottom connectors excluded)
Connection
  Power
: Separable tension clamp terminal
  Applicable wire size: 0.2 to 1.5 mm2, stripped
  length 10 mm
  Network: RJ-45 Modular Jack
Recommended solderless terminal
  AI0,5-10WH 0.5mm2 (Phoenix Contact)
  AI0,75-10GY 0.75mm (Phoenix Contact)
Housing material: Flame-resistant resin (white)
Lens: Flame-resistant resin (transparent)
Isolation: Network to power input to FE1 (Functional Earth)
DIP SW Setting: Frequency of lamp blinking and buzzing discontinuance, buzzing volume level and output at connection failed. (refer to the instruction manual)
Lamp: Red, amber, green, blue and white LEDs
on/blinking (approx. 2 Hz, 10 Hz)
Indicator LEDs: Power, Run, Link, Link100, COL (5 LEDs) indicate the module’s operating conditions. (Refer to the insruction manual)
Buzzing: Approx. 3.3 kHz
  Interval: continuous/intermittent (approx. 2 Hz, 10 Hz)

COMMUNICATION
Communication Standard: IEEE 802.3u
Transmission: 10BASE-T, 100BASE-TX
Baud rate: 10/100 Mbps (Auto Negotiation function)
Protocol: Modbus/TCP
Data: RTU (Binary)
Max. number of socket connections: 2
Transmission media: 10BASE-T (STP, Category 5) 100BASE-TX (STP, Category 5e)
Max. length of fieldbus segment: 100 meters
IP address: 192.168.0.1 (factory setting);
Selectable with PC Configurator Software
Port No.: 502
Ethernet indicator LED: Link, Link100, COL

INSTALLATION
Power consumption
AC: Approx. 6 VA at 100 V
  Approx. 8 VA at 200 V
  Approx. 9 VA at 240 V
DC: Approx. 3 W
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Atmosphere: No corrosive gas
Mounting: Direct mounting
Mounting direction: Vertical
Weight: 1.4 kg (3.1 lb)

PERFORMANCE
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @ 1 minute
(network to power to FE1)

STANDARDS & APPROVALS
Refer to the manuals to comply with the standards.
EU conformity:
EMC Directive 
  EN 60947-5-1
Low Voltage Directive 
 EN 60947-5-1
  ・24 V DC power
   Installation Category III
   Pollution Degree 3
  ・100 – 240 V AC power
   Installation Category II
   Pollution Degree 2
  Network to power: Reinforced insulation (300 V)
RoHS Directive
  EN 50581
Protection against access to the terminal blocks:
Finger protection (VDE 0660-514)

EXTERNAL VIEW

TERMINAL ASSIGNMENTS

DIMENSIONS unit: mm

MOUNTING REQUIREMENTS unit: mm

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

M-System Co., Ltd.