ES-2411 Rev.10
PV
Plug-in Signal Conditioners M-UNIT
P/I TRANSDUCER
Functions & Features
• Converting a standard pneumatic signal into a proportional DC output
• High-density mounting
Typical Applications
• Converting a pneumatic system into a 4 – 20 mA for indicating and controlling in DCS system
MODEL: PV-[1]–[2][3]
ORDERING INFORMATION
• Code number: PV-[1]-[2][3]
Specify a code from below for each of [1] through [3].
(e.g. PV-A-B/A2S/P7)
• Special output range (For codes Z & 0)
[1] OUTPUT
Current
A
: 4 – 20 mA DC (Load resistance 750 Ω max.)
B
: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C
: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D
: 0 – 20 mA DC (Load resistance 750 Ω max.)
E
: 0 – 16 mA DC (Load resistance 900 Ω max.)
F
: 0 – 10 mA DC (Load resistance 1500 Ω max.)
G
: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z
: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
1
: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2
: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3
: 0 – 1 V DC (Load resistance 100 Ω min.)
4
: 0 – 10 V DC (Load resistance 1000 Ω min.)
5
: 0 – 5 V DC (Load resistance 500 Ω min.)
6
: 1 – 5 V DC (Load resistance 500 Ω min.)
4W
: -10 – +10 V DC (Load resistance 2000 Ω min.)
0
: Specify voltage (See OUTPUT SPECIFICATIONS)
[2] POWER INPUT
AC Power
B
: 100 V AC
C
: 110 V AC
D
: 115 V AC
F
: 120 V AC
G
: 200 V AC
H
: 220 V AC
J
: 240 V AC
DC Power
S
: 12 V DC
R
: 24 V DC
V
: 48 V DC
[3] OPTIONS (multiple selections)
Input
blank
: 0.2 – 1.0 kgf/cm
2
/A1S
: 19.6 – 98.1 kPa
/A2S
: 20 – 100 kPa
/A3S
: 20.7 – 103.4 kPa
/A2
: 0.2 – 1.0 bar
/A3
: 3 – 15 psig
Pneumatic Connection
blank
: Rc 1/4"
/P7
: 1/4" NPT fitting
GENERAL SPECIFICATIONS
Construction
: Plug-in
Connection
Output & power input
: M3.5 screw terminals;
torque 0.8 N·m
Pneumatic
: Rc 1/4" or 1/4" NPT female; torque ≤ 12 N·m
Material
Housing
: Flame-resistant resin (black)
Base socket
: Die cast aluminium
Screw terminals
: Nickel-plated steel
Isolation
: Output to power
Zero adjustment
: -5 to +5 % (front)
Span adjustment
: 95 to 105 % (front)
INPUT SPECIFICATIONS
■
Input
19.6 – 98.1 kPa, 0.2 – 1.0 kgf/cm
2
20 – 100 kPa, 0.2 – 1.0 bar
20.7 – 103.4 kPa, 3 – 15 psig
OUTPUT SPECIFICATIONS
■ DC Current
: 0 – 20 mA DC
Minimum span
: 1 mA
Offset
: Max. 1.5 times span
Load resistance
: Output drive 15 V max.
■
DC Voltage
: -10 – +12 V DC
Minimum span
: 5 mV
Offset
: Max. 1.5 times span
Load resistance
: Output drive 10 mA max.; 5 mA for negative voltage output; at ≥ 0.5 V
INSTALLATION
Power input
•
AC
: Operational voltage range: rating ±10 %,
50/60 ±2 Hz, approx. 2 VA
•
DC
: Operational voltage range: rating ±10 %,
ripple 10 %p-p max., approx. 2 W (90 mA at 24 V)
Operating temperature
: -5 to +60°C (23 to 140°F)
Operating humidity
: 30 to 90 %RH (non-condensing)
Mounting
: Surface
Weight
: 550 g (1.21 lb)
PERFORMANCE in percentage of span
Accuracy
: ±0.3 %
Temp. coefficient
: ±0.03 %/°C (±0.02 %/°F)
Response time
: 1.5 sec. (0 – 90 %)
Permissible overrange
: 196 kPa (2.0 kgf/cm
2
, 1.96 bar, 28 psig)
Line voltage effect
: ±0.1 % over voltage range
Insulation resistance
: ≥ 100 MΩ with 500 V DC
Dielectric strength
: 2000 V AC @ 1 minute
(output to power to housing)
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch]
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM